top of page
idea.png

Energy

One-stop solution for Substation Condition Monitoring and Diagnosis

The growing electricity demand is making power systems more complex. To meet this demand and follow strict guidelines, utilities must ensure an uninterrupted supply, avoiding breakdowns or grid failures.

​

Major maintenance is costly and must be planned based on equipment condition and age. It’s better to assess equipment health and address issues proactively than risk system failures.

​​

Advancements in technology have introduced new condition-monitoring tools essential for maintenance. Test results from these instruments should be compared with previous data to assess current equipment health, emphasizing the need for a test result database for accurate evaluation.

​

​Testing is critical to condition monitoring and must be done carefully to avoid incorrect conclusions.

​

At Genesis, we recommend the PPPM method—Planned, Periodic, and Preventive Maintenance. This approach minimizes breakdowns, improves system reliability, and generates revenue, especially in older substations where equipment is more prone to failure.

Power Transformer

 Power Transformer Diagnosis

  • Capacitance & Tan delta Measurement 

  • SFRA ( Sweep Frequency Response ) 

  • Advanced Three Phase Turns Ratio Measurement

  • Winding Resistance Measurement up to 100 A

  • Dielectric Frequency Spectroscopy Analysis

  • Demagnetization

  • Short-Circuit Impedance / Leakage Reactance

  • Frequency Response of Stray Losses

  • Three-Phase OLTC Scan / Dynamic Resistance (DRM)

  • Vector Group Check

  • Partial Discharge Measurement 

 Circuit Breaker Diagnosis

  • Factory Acceptance Tests

  • Dynamic Contact Resistance Measurement(DCRM)

  • Timing and Bounces of Main & PIR Contacts

  • Static Contact Resistance Measurement

  • Coil Resistance / Current Measurement

  • Mechanism Travel Measurement

  • SF6 Dew Point, Purity, and SO2 Measurement

  • Partial Discharge Measurement of Switchgears

  • High Voltage Test

Circuit Breaker
Instrument Transformers

 Instrument Transformer Diagnosis

  • Power/dissipation factor 

  • capacitance measurements 

  • Automated testing with multi-tap CT module

  • Multi-Tap Ratio Error and phase Error tests 

  • Winding resistance measurement 

  • Excitation characteristics (knee points)

  • Composite errors (ALF, ALFi, FS, FSi, Vb)

  • Burden impedance measurement

  • Partial Discharge Measurement 

  • Insulation Resistance measurement

  • High Current Primary Injection

  • Stability and Scheme Check​

 Relays and Protection Testing

  • Scheme Checking during the Commissioning

  • Complete Engineering and Design of Panels

  • Relay Testing with Three-phase Kits 

  • Relay Testing with Single-Phase Kits

  • Advanced Distance Relay Testing

  • Differential Relay Testing 

  • Bus Bar Relay Testing and Configuration

  • Logic Configuration and Testing

  • Relay Retrofitting

  • System-based protection testing

  • Transient power system simulation

C&R panel
Battery

 Battery Capacity with Advanced

 Load Tester

The capacity test is conducted in accordance with established battery testing standards, including IEEE 450-2010, IEEE 1188-2005, IEEE 1106-2015, and IEC 60896-11/22, as well as other relevant and applicable standards. We can perform this test using the following discharge modes and it allows us to evaluate the battery's capacity accurately under different conditions, ensuring adherence to the specified standards.​

  • Constant Current

  • Constant Power

  • Constant Resistance

​

Thermal Imaging 

We offer expert thermal inspections for electrical systems, mechanical equipment, and buildings, helping you detect issues, prevent breakdowns, and boost efficiency. We offer below Thermography services.​

  • Medical

  • Electrical

  • Structural

  • Mechanical

  • Water Leak Detection

  • Compressed Air Leak Detection

  • Drone Audit & Inspection

​

Thermovision
Blueprint Design

 2D/3D Design & Drafting Services

Outsource CAD drafting to us for cost-effective solutions, including drawing, modeling, and architectural, electrical, structural, and mechanical drafting. From design conceptualization to prototyping and optimization, we provide tailored services that streamline your process, accelerate timelines, and elevate your 2D and 3D designs. Partner with us to enhance efficiency and profitability in your projects.

​

Together, we can make a difference

Proven Expertise: With our deep experience in retail development, we help businesses drive sustainable growth and boost customer engagement with the latest technologies and strategies. Our experienced developers, designers, and business analysts work closely with you to understand your goals and deliver custom solutions that drive results.

 

Customized Solutions: We work closely with you to create strategies tailored to your unique business goals, helping you connect with customers in meaningful ways. Our client-first approach ensures that each solution is aligned with your unique business needs and objectives. Your success is our success.

Customized Solutions: We work closely with you to create strategies tailored to your unique business goals, helping you connect with customers in meaningful ways. Our client-first approach ensures that each solution is aligned with your unique business needs and objectives. Your success is our success.

 

Tailored Strategies: We understand that every retail business is unique. That's why we don't offer one-size-fits-all solutions. Instead, we work with you to create customized solutions that align with your specific goals, challenges, and target audience. Whether you're looking to increase sales, enhance customer engagement, or streamline operations, our customized approach ensures that every solution is designed to deliver results that are as unique as your business.

bottom of page